Marantz SR7002 User Manual

The Marantz SR7002 is a high-performance 7.1 channel AV receiver featuring 125 watts per channel, HDMI 1.3a connectivity, Dolby TrueHD and DTS-HD Master Audio decoding, Audyssey MultEQ XT room calibration, network audio streaming, multi-zone capability, and advanced video processing. Below are key sections for setup, operation, features, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting Devices 7. Audio Setup and Calibration 8. Network Features 9. Multi-Zone Operation 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: 7.1 channel amplifier, HDMI switching, network connectivity, Audyssey room correction, multi-zone capability.

Feature	Description
Power Output	125W x 7 channels (8 ohms, 20Hz-20kHz)
HDMI Inputs	4 HDMI 1.3a inputs with audio return channel
Audio Decoding	Dolby TrueHD, DTS-HD Master Audio
Room Correction	Audyssey MultEQ XT auto calibration
Network Audio	Ethernet connectivity for streaming audio
Multi-zone	Zone 2 and Zone 3 audio output
Video Processing	Faroudja DCDi video scaling
Inputs	Component video, composite, digital audio
Outputs	7.1 pre-outs, multi-zone outputs
Remote Control	Learning remote with backlight

Installation

Unpack and inspect contents. Place in well-ventilated area.

Connect speakers: Match polarity (+/-) for all 7.1 channels.
Connect HDMI sources: Use HDMI inputs for Blu-ray, gaming consoles, etc.
Connect video display: HDMI output to TV or projector.
Connect network: Ethernet cable for streaming features.
Plug into AC power.

WARNING! Ensure adequate ventilation; do not block cooling vents. Use proper gauge speaker wire.

First-Time Setup

Power on receiver; follow on-screen setup wizard.

Run Audyssey calibration: Connect included microphone and follow prompts.
Configure inputs: Assign sources to HDMI and other inputs.
Set speaker configuration: Specify speaker sizes and distances.
Configure network: Set up Ethernet or wireless adapter.
Set multi-zone options: Configure Zone 2/3 if needed.

CAUTION! Keep magnetic fields away from CRT displays during setup.

Specifications

Amplifier Section: 125W x 7 channels (8 ohms, 20Hz-20kHz, 0.08% THD)
Frequency Response: 10Hz-100kHz (+1/-3 dB)
Signal-to-Noise Ratio: 100 dB (line level)
HDMI: 4 inputs, 2 outputs (1.3a specification)
Digital Audio: 4 optical, 2 coaxial inputs
Video: Component video (3 in, 1 out), composite video (5 in, 2 out)
Network: Ethernet port, optional wireless adapter
Multi-zone: Zone 2 and Zone 3 pre-outs
Power Consumption: 650W maximum
Dimensions: 17.3" W x 6.8" H x 17.7" D

Controls and Settings

Access OSD via remote or front panel display. Front Panel: POWER, INPUT SELECT, VOLUME, SETUP, TONE.

Remote: POWER, INPUT SELECT, VOLUME, MUTE, SETUP, AUDIO MODE, ZONE SELECT, numeric buttons.

Audio Settings: Speaker levels, crossover, distance, EQ settings. Video Settings: Resolution, aspect ratio, video mode. Network Settings: IP configuration, streaming services. System Settings: OSD language, firmware updates.

Connecting Devices

HDMI: Primary connection for HD sources. Component/Composite: Legacy video sources. Digital Audio: Optical/coaxial for audio-only sources.

Turn off all devices before connecting.
Use high-speed HDMI cables for 1080p signals.
Assign inputs in setup menu for easy selection.
Connect network cable for streaming features.

Tip: Use HDMI for both audio and video when possible for best quality.

Audio Setup and Calibration

Use Audyssey MultEQ XT for optimal room acoustics.

Place microphone at primary listening position.
Run auto calibration from setup menu.
Verify speaker configuration after calibration.
Manual adjustments: Speaker levels, distance, crossover.
Audio modes: Dolby Surround, DTS Neo:6, stereo modes.

WARNING! Ensure quiet environment during calibration for accurate results.

Network Features

Stream audio from network sources and internet radio.

Connect Ethernet cable or wireless adapter.
Configure network settings in setup menu.
Access streaming services: Internet radio, network shares.
Control via web interface or mobile app.

Supported formats: MP3, WMA, WAV, FLAC, AAC.

Multi-Zone Operation

Control audio in multiple rooms simultaneously.

Zone 2: Stereo audio to second room.
Zone 3: Additional audio zone with independent source.
Source selection: Different sources in main zone and multi-zones.
Volume control: Independent volume for each zone.

Note: Multi-zone operation may limit main zone format capabilities.

Regulatory Information

FCC Part 15: Class B digital device compliant. CE marked for European market. Manufactured under license from Dolby Laboratories and DTS. For support, visit www.marantz.com or contact authorized service centers. Firmware updates available online.

Troubleshooting

Symptom	Possible Cause	Corrective Action
No sound from speakers	Input selection/speaker wires	Check input selection; verify speaker connections; ensure not muted.
No video through receiver	HDMI handshake/resolution	Power cycle devices; check HDMI cable; verify video resolution.
Network not connecting	Cable/network settings	Check Ethernet cable; verify network settings; restart router.
Remote not working	Batteries/obstructions	Replace batteries; ensure clear path to IR sensor; check mode selection.
Overheating	Ventilation blockage	Ensure adequate ventilation; clear vents; check ambient temperature.

Reset: Press and hold STATUS and ENTER while powering on for factory reset.

Service: Authorized Marantz service centers; www.marantz.com