Marantz SR6005 Setup Manual

The Marantz SR6005 is a high-performance 7.2 channel AV receiver featuring 110W per channel, HDMI 1.4a connectivity, Audyssey MultEQ XT room calibration, network streaming capabilities, AirPlay support, Dolby TrueHD and DTS-HD Master Audio decoding, multi-room audio, and advanced video processing. Below are key sections for setup, features, installation, configuration, operation, and troubleshooting.

Features at a Glance

Key components: 7.2 channel amplifier, Audyssey MultEQ XT calibration, HDMI switching, network audio streaming, multi-zone capability.

Feature	Description
Power Output	110W per channel (8 ohms, 20Hz-20kHz)
HDMI Inputs	6 inputs, 1 output (HDMI 1.4a)
Network Connectivity	Ethernet and Wi-Fi (optional adapter)
Audio Decoding	Dolby TrueHD, DTS-HD Master Audio
Room Calibration	Audyssey MultEQ XT with setup microphone
Multi-room Audio	Zone 2 and Zone 3 capability
Streaming Services	AirPlay, internet radio, DLNA
Video Processing	Faroudja DCDi Cinema upscaling to 1080p
Inputs/Outputs	Component video, composite, optical/coaxial digital
Remote Control	RC018SR learning remote with backlight

Unpacking and Inspection

Carefully unpack and verify all components are present.

1. Main unit: Marantz SR6005 receiver
2. Remote control: RC018SR with batteries
3. Setup microphone: Audyssey calibration mic
4. Power cord: Standard AC power cable
5. AM loop antenna and FM wire antenna
6. Quick start guide and warranty information

WARNING! Unit is heavy (12.3 kg); use proper lifting technique. Keep packaging for future transport.

Initial Setup and Installation

Follow these steps for proper installation and initial configuration.

1. Placement: Ensure adequate ventilation (minimum 10cm clearance on all sides)
2. Speaker connections: Connect speakers using appropriate gauge wire
3. Source connections: Connect HDMI devices, gaming consoles, Blu-ray players
4. Network connection: Connect Ethernet cable or install Wi-Fi adapter
5. Power connection: Connect to grounded AC outlet
6. Initial power on: Press front panel power button

CAUTION! Ensure proper ventilation to prevent overheating. Do not block ventilation slots.

Technical Specifications

• Amplifier Section: 7.2 channels, 110W per channel (8Ω)
• Frequency Response: 10Hz-100kHz (+1/-3dB)
• Total Harmonic Distortion: 0.05% (8Ω, 20Hz-20kHz)
• Signal-to-Noise Ratio: 100dB (IHF-A weighted)
• HDMI: 6 inputs, 1 output (3D, ARC, Deep Color)
• Digital Inputs: 2 optical, 2 coaxial
• Analog Inputs: 6 stereo pairs, phono input
• Network: Ethernet, optional Wi-Fi (UWF-1)
• Power Consumption: 650W maximum, 65W standby
• Dimensions: 440 x 395 x 167mm (W x D x H)
• Weight: 12.3 kg

Front Panel Controls

Front panel includes power button, input selector, volume knob, display, and various function buttons.

Main Controls: POWER, INPUT SELECTOR, MASTER VOLUME, MUTE, PHONES, SPEAKERS A/B, TONE, AUDIO, MOVIE, MUSIC, STATUS, SETUP.

Display Indicators: Input source, volume level, audio format, network status, zone indicators.

Hidden Compartment: Contains setup buttons, HDMI input, USB port, video input.

Speaker Connection and Configuration

Proper speaker setup is crucial for optimal audio performance.

1. Speaker terminals: Use banana plugs or bare wire connections
2. Wire gauge: 12-16 AWG recommended for most installations
3. Polarity: Ensure correct positive/negative connections
4. Speaker placement: Follow Dolby recommended positioning
5. Audyssey setup: Run automatic room calibration with included microphone
6. Manual adjustments: Fine-tune speaker levels and distances

Tip: Run Audyssey calibration in a quiet room for best results.

Network Setup and Streaming

Network connectivity enables streaming services and multi-room audio.

1. Wired connection: Connect Ethernet cable to router
2. Wireless connection: Install UWF-1 Wi-Fi adapter (sold separately)
3. Network configuration: Automatic (DHCP) or manual IP assignment
4. Streaming services: Access internet radio, Spotify, Pandora
5. AirPlay: Stream audio from Apple devices
6. DLNA: Access music from network storage devices
7. Firmware updates: Check for latest firmware via network

WARNING! Ensure stable network connection for streaming services.

Advanced Audio Settings

Customize audio performance with advanced settings and processing.

Audyssey Settings: MultEQ XT, Dynamic EQ, Dynamic Volume, LFC (Low Frequency Containment)

Sound Modes: Auto, Direct, Pure Direct, Dolby Surround, DTS Neo:6, Stereo

Tone Controls: Bass, Treble, Loudness compensation

Multi-room Audio: Zone 2 and Zone 3 configuration, independent source selection

Lip Sync: Adjustable audio delay for synchronization

Maintenance and Care

Proper maintenance ensures long-term reliability and performance.

Cleaning: Use dry, soft cloth. Do not use chemical cleaners.

Ventilation: Keep vents clear of dust and obstructions

Firmware: Regularly check for and install firmware updates

Connections: Periodically check cable connections for tightness

CAUTION! Unplug unit before cleaning. Do not open chassis - no user-serviceable parts inside.

Regulatory Information

FCC Compliance: This device complies with Part 15 of FCC Rules. CE Mark: Complies with European directives. RoHS compliant. Manufactured under license from Dolby Laboratories. DTS and DTS-HD are registered trademarks. Audyssey Laboratories technology incorporated. For support, visit www.marantz.com or contact authorized service centers.

Troubleshooting Guide

Symptom	Possible Cause	Corrective Action
No power	Power cord, outlet, protection mode	Check power connection; reset circuit breaker; check for shorts
No sound	Input selection, volume, mute	Verify input source; check volume level; disable mute
No video	HDMI connection, input selection	Check HDMI cables; verify input source; try different HDMI input
Network connection issues	Ethernet cable, router settings	Check cable connection; verify network settings; restart router
Remote not working	Batteries, obstacles, distance	Replace batteries; ensure line of sight; reduce distance
Overheating	Insufficient ventilation	Ensure adequate clearance; clean ventilation slots

Factory Reset: Press and hold CURSOR UP and STATUS buttons while powering on.

Service: Contact authorized Marantz service center. Do not attempt internal repairs.