marantz sr 96 user manual download

The Marantz SR 96 is a high-performance AV receiver featuring Dolby Digital and DTS surround sound processing, multiple audio/video inputs, advanced tuning capabilities, and robust connectivity options. This comprehensive manual covers setup, operation, troubleshooting, and maintenance for optimal performance. Below are key sections covering features, installation, configuration, operation, and support.

1. Features Overview 2. Installation Guide 3. Initial Setup 4. Technical Specifications 5. Controls and Functions 6. Connection Setup 7. Audio Configuration 8. Video Settings 9. Maintenance & Care 10. Compliance Information 11. Troubleshooting Guide

Features Overview

Key components: High-power amplifier section, Dolby Digital/DTS decoder, Multiple audio/video inputs, Remote control, Speaker terminals, Digital optical/coaxial inputs.

Feature	Description
Power Output	100W per channel (8 ohms, 20Hz-20kHz)
Audio Decoding	Dolby Digital, DTS, Pro Logic
Inputs	6 audio, 4 video, 2 digital optical, 1 coaxial
Outputs	5.1 channel pre-outs, tape monitor, video monitor
Tuner	AM/FM with 30 station presets
Remote Control	Full-function learning remote
Speaker Terminals	5-channel binding posts
Display	Fluorescent display with dimmer
Setup Memory	Custom settings storage
Protection Circuitry	Overload, short circuit, thermal protection

Installation Guide

Unpack and verify all components. Choose well-ventilated location.

Connect speakers: Use appropriate gauge wire for front, center, surround channels.
Connect audio sources: CD player, tape deck, turntable to corresponding inputs.
Connect video sources: DVD player, VCR, cable box to video inputs.
Connect antennas: AM loop and FM wire antennas to designated terminals.
Plug into AC power outlet.

WARNING! Ensure adequate ventilation space around unit. Do not block ventilation openings.

Initial Setup

Power on receiver; follow setup procedure.

Speaker configuration: Set speaker size (large/small) and distance.
Input assignment: Assign sources to appropriate inputs.
Tuner setup: Auto-scan and store FM/AM stations.
Audio calibration: Use test tone for channel balance.
Remote programming: Program remote for other components.

CAUTION! Disconnect power before making any cable connections.

Technical Specifications

Power Output: 100W x 5 (8 ohms, 20Hz-20kHz, 0.08% THD)
Frequency Response: 10Hz-100kHz (+1/-3dB)
Signal-to-Noise Ratio: 100dB (line inputs)
Total Harmonic Distortion: 0.08% (rated power)
Input Sensitivity: 200mV (line), 2.5mV (MM phono)
Tuner Section: FM/AM with 30 presets
Digital Inputs: 2 optical, 1 coaxial
Video Bandwidth: 10MHz (-3dB)
Power Consumption: 450W maximum
Dimensions: 440mm W x 161mm H x 464mm D
Weight: 14.5 kg

Controls and Functions

Front panel: POWER, INPUT SELECT, VOLUME, TUNING, MEMORY, SPEAKERS A/B.

Remote: POWER, INPUT SELECT, VOLUME, MUTE, TUNER MEMORY, SURROUND MODE, TEST TONE.

Audio: Bass, treble, balance, loudness, surround mode (Dolby Digital, DTS, Pro Logic). Video: Input selection, monitor out. Tuner: Auto/manual tuning, preset memory. System: Speaker configuration, input rename, factory reset.

Connection Setup

Audio: Phono, CD, tape, DVD, aux inputs. Video: Composite/S-video inputs. Digital: Optical/coaxial for Dolby Digital/DTS.

Turn off all components before connecting.
Use high-quality cables for best performance.
Connect digital sources for surround sound processing.
Select appropriate input source on front panel or remote.

Tip: Use digital connections for DVD players to access Dolby Digital and DTS formats.

Audio Configuration

Advanced audio settings for optimal sound quality.

Speaker levels: Adjust individual channel levels using test tone.
Crossover settings: Set appropriate crossover frequency for small speakers.
Surround modes: Select Dolby Digital, DTS, or Pro Logic as needed.
Tone controls: Adjust bass/treble to room acoustics.
Loudness: Engage for better low-volume listening.

Note: Use auto calibration for initial setup, then fine-tune manually.

Video Settings

Video processing and routing options.

Input selection: Assign video sources to corresponding inputs.
Monitor output: Connect to TV or projector.
Video conversion: Composite to S-video upconversion.
OSD setup: Adjust on-screen display settings.

WARNING! Ensure video cables are securely connected to avoid signal loss.

Maintenance & Care

Unplug unit before cleaning. Use soft, dry cloth. Avoid chemical cleaners.

CAUTION! Do not use liquid cleaners. Keep away from moisture and extreme temperatures.

Compliance Information

FCC Part 15 Class B compliant. CE marked. RoHS compliant. Manufactured under license from Dolby Laboratories. DTS and DTS Digital Surround are registered trademarks. For technical support, visit www.marantz.com or contact authorized service centers.

Troubleshooting Guide

Symptom	Possible Cause	Corrective Action
No power	Power cord, outlet	Check power connection; try different outlet; check fuse.
No sound	Speaker connections, input selection	Verify speaker wires; check input selection; adjust volume.
Poor FM reception	Antenna placement	Reposition FM antenna; ensure proper connection.
Remote not working	Batteries, obstruction	Replace batteries; ensure clear path to sensor.
Overheating	Ventilation, impedance	Ensure adequate ventilation; check speaker impedance.
No surround sound	Source, connections	Verify digital connection; check source output format.

Reset: Press TUNER + PRESET 1 + POWER simultaneously for factory reset.

Support: www.marantz.com | Authorized service centers worldwide