Marantz SR 92 User Manual

The Marantz SR 92 is a high-performance AV receiver featuring Dolby Digital and DTS decoding, 7-channel amplification, multi-room audio capability, digital audio inputs, component video switching, and advanced room calibration. With 100 watts per channel, this receiver delivers exceptional audio quality for home theater systems. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting Devices 7. Audio Setup & Calibration 8. Multi-Room Operation 9. Care & Maintenance 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: 7-channel amplifier, Dolby Digital/DTS decoder, multi-room audio system, component video switching, digital audio inputs, remote control, and room calibration microphone.

Feature	Description
Power Output	100 watts per channel (8 ohms, 20Hz-20kHz)
Audio Decoding	Dolby Digital, DTS, Dolby Pro Logic II
Inputs	6 analog audio, 3 digital optical, 2 digital coaxial
Video Inputs	3 component video, 4 composite video
Multi-room	Zone 2 audio output capability
Room Calibration	Auto setup with included microphone
Speaker Terminals	7-channel binding posts
Remote Control	Learning remote with backlight
Display	Fluorescent display with dimmer control
Power Consumption	550 watts maximum

Installation

Unpack and inspect contents. Place receiver in well-ventilated area.

Connect speakers: Use speaker wire to connect front, center, surround, and surround back channels.
Connect audio sources: Use analog or digital inputs for CD player, DVD player, etc.
Connect video sources: Use component or composite inputs for video devices.
Connect subwoofer: Use subwoofer pre-out for powered subwoofer.
Plug into AC power.

WARNING! Ensure adequate ventilation around receiver; do not block ventilation holes.

First-Time Setup

Power on receiver; follow on-screen prompts or front panel display.

Auto calibration: Connect calibration microphone; run auto setup from menu.
Speaker configuration: Set speaker sizes (Large/Small) and crossover frequencies.
Input assignment: Assign audio/video inputs to source buttons.
Audio settings: Configure bass management and delay settings.
Remote setup: Program remote control for other devices.

CAUTION! Do not move microphone during auto calibration process.

Specifications

Power Output: 100W x 7 (8 ohms, 20Hz-20kHz, 0.08% THD)
Frequency Response: 10Hz-100kHz (+1/-3dB)
Signal-to-Noise Ratio: 100dB (IHF-A)
Total Harmonic Distortion: 0.08% (20Hz-20kHz)
Input Sensitivity: 200mV (line)
Video Bandwidth: 100MHz (-3dB)
Digital Inputs: 3 optical, 2 coaxial
Analog Inputs: 6 stereo pairs
Power Requirements: 120V AC, 60Hz
Dimensions: 17-3/8" W x 6-3/4" H x 17-1/2" D
Weight: 35.3 lbs

Controls and Settings

Access menu system via front panel or remote control. Front Panel: POWER, VOLUME, INPUT SELECT, TONE, MUTE.

Remote: POWER, Numeric buttons, INPUT SELECT, VOLUME, MUTE, MENU, CURSOR buttons, ENTER, TEST TONE.

Audio Settings: Speaker levels, distance, crossover, tone controls. Video Settings: Input assignment, resolution. System Settings: OSD language, remote control setup. Listening Modes: Dolby Digital, DTS, Stereo, Direct, Pure Direct.

Connecting Devices

Audio Sources: CD player, turntable (with phono preamp), tape deck. Video Sources: DVD player, Blu-ray player, cable/satellite box, gaming console.

Turn off receiver and devices before connecting.
Use high-quality cables for best performance.
Match digital inputs to compatible sources.
Assign inputs in receiver menu system.

Tip: Use component video cables for high-definition video sources.

Audio Setup & Calibration

Auto calibration system with included microphone.

Place microphone at primary listening position.
Access auto setup from main menu.
Follow on-screen instructions; remain quiet during test tones.
Review and adjust results if necessary.
Manual adjustments: Speaker levels, distance, crossover settings.
Listening mode selection for different content types.

WARNING! Do not disconnect microphone during calibration process.

Multi-Room Operation

Zone 2 capability for second room audio.

Connect Zone 2 speakers to dedicated terminals.
Configure Zone 2 settings in menu system.
Select source for Zone 2 operation.
Control volume independently from main zone.

Note: Zone 2 operates in stereo mode only.

Care & Maintenance

Unplug before cleaning. Use soft, dry cloth for exterior; compressed air for ventilation holes.

CAUTION! Do not use liquid cleaners; avoid moisture near ventilation openings.

Regulatory Information

FCC Part 15: Class B digital device; complies with interference limits for residential use. Copyright © Marantz America, Inc. Dolby and DTS are registered trademarks. For support, visit www.marantz.com or contact customer service at 1-800-270-2744.

Troubleshooting

Symptom	Possible Cause	Corrective Action
No sound from speakers	Speaker connections/mute	Check speaker wires; ensure mute is off; verify input selection.
No video display	Video connections/settings	Check video cables; verify input assignment; check display device.
Remote control not working	Batteries/obstructions	Replace batteries; ensure clear path to IR sensor; check remote mode.
Overheating	Insufficient ventilation	Ensure adequate space around receiver; check ventilation openings.
No digital audio	Input assignment/cables	Verify digital input assignment; check optical/coaxial cables.

Reset: Press and hold POWER and SURROUND MODE buttons for 5 seconds.

Service: 1-800-270-2744; www.marantz.com