Marantz SR-7000G Manual

The Marantz SR-7000G is a high-performance AV receiver featuring Dolby Digital and DTS surround sound processing, 100 watts per channel (8 ohms), 6-channel amplification, multiple audio/video inputs, digital optical/coaxial inputs, AM/FM tuner with 30 presets, speaker setup calibration, remote control, and advanced audio adjustments. Powered by 120V AC, 60Hz. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting Devices 7. Audio Setup and Calibration 8. Remote Control Functions 9. Care & Maintenance 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: 6-channel amplifier, Dolby Digital/DTS decoder, Remote Control, Multiple audio/video inputs, Digital optical/coaxial inputs, Speaker terminals, AM/FM antenna terminals.

Feature	Description
Power output	100W x 6 channels (8 ohms, 20Hz-20kHz)
Surround formats	Dolby Digital, DTS, Dolby Pro Logic
Audio inputs	6 analog, 2 digital optical, 1 coaxial
Video inputs	3 composite, 2 S-Video
Speaker terminals	Front, Center, Surround, Subwoofer
Tuner	AM/FM with 30 station presets
Remote control	Learning remote with macro functions
Setup microphone	Auto speaker calibration
Headphone jack	Front panel 1/4" stereo jack
AC power	120V AC, 60Hz operation

Installation

Unpack and inspect contents. Place in well-ventilated area.

Connect speakers: Match polarity (+/-) for front, center, surround channels.
Connect subwoofer: Use subwoofer pre-out or speaker level connections.
Connect source devices: Use appropriate audio/video inputs for DVD, cable box, etc.
Connect antennas: AM loop and FM wire antennas to respective terminals.
Plug into AC power outlet.

WARNING! Ensure proper ventilation; do not block cooling vents. Use correct speaker impedance.

First-Time Setup

Power on receiver; follow on-screen display or front panel indicators.

Auto speaker setup: Connect calibration microphone, run auto setup procedure.
Manual speaker settings: Adjust distance, level, and crossover for each channel.
Input assignment: Assign digital/analog inputs to source components.
Tuner setup: Auto-scan and store AM/FM stations.
Surround mode: Select default listening mode for each input.

CAUTION! Allow adequate clearance around unit for proper heat dissipation.

Specifications

Power Output: 100W x 6 channels (8 ohms, 20Hz-20kHz, 0.08% THD)
Frequency Response: 10Hz-100kHz (+1/-3dB)
Signal-to-Noise: 100dB (line inputs)
Total Harmonic Distortion: 0.08% (20Hz-20kHz)
Input Sensitivity: 200mV (line), 2.5mV (MM phono)
Digital Inputs: 2 optical, 1 coaxial
Video Inputs: 3 composite, 2 S-Video
Speaker Impedance: 6-16 ohms
Power Consumption: 450W maximum
Dimensions: 17-1/8" W x 6-3/4" H x 16-1/4" D
Weight: 28.7 lbs

Controls and Settings

Access setup via front panel buttons or remote control. Front Panel: POWER, VOLUME, INPUT SELECT, SURROUND MODE, TUNER PRESETS.

Remote: POWER, INPUT SELECT, VOLUME, MUTE, SURROUND MODE, NUMERIC, TUNER, SETUP, TEST TONE.

Audio: Bass, Treble, Balance, Loudness, Night mode. Video: Input source selection, video conversion. Speaker: Distance, Level, Crossover, Size. Tuner: Preset memory, Auto scan, Manual tuning. System: Input rename, Default settings, Firmware version.

Connecting Devices

Audio sources: CD player, turntable, tape deck. Video sources: DVD, cable/satellite, gaming console.

Turn off receiver and components before connecting.
Use high-quality cables for best performance.
Assign digital inputs in setup menu for compatible sources.
Connect video monitor to monitor output.
Select input via front panel or remote control.

Tip: Use digital connections for Dolby Digital/DTS sources for optimal sound quality.

Audio Setup and Calibration

Auto calibration with setup microphone or manual adjustment.

Auto setup: Place microphone at listening position, follow on-screen prompts.
Manual speaker settings: Adjust level, distance, and crossover for each channel.
Surround modes: Select Dolby Digital, DTS, or Pro Logic for each source.
Audio adjustments: Bass, treble, loudness compensation.
Test tone: Use built-in test tone for manual level adjustment.

WARNING! Ensure proper speaker phase and placement for optimal surround effect.

Remote Control Functions

Learning remote with macro capability for system control.

Button	Function
POWER	Turns receiver on/standby
INPUT SELECT	Cycles through source inputs
VOLUME +/-	Adjusts master volume
MUTE	Temporary audio mute
SURROUND MODE	Selects decoding mode
TEST TONE	Activates speaker test
SETUP	Accesses menu system
NUMERIC	Direct input selection/tuner presets
LEARN	Programming mode for other devices
MACRO	Stores multiple command sequences

Care & Maintenance

Unplug before cleaning. Use soft, dry cloth for exterior. Compressed air for vents.

CAUTION! Do not use liquid cleaners. Keep away from moisture and extreme temperatures.

Regulatory Information

FCC Part 15: Class B digital device; complies with interference limits for residential use. Copyright © Marantz America, Inc. Dolby and DTS are registered trademarks. For support, visit www.marantz.com or contact 1-800-270-2744.

Troubleshooting

Symptom	Possible Cause	Corrective Action
No sound	Input selection/volume	Check input selection; adjust volume; verify speaker connections.
No surround sound	Source/decoder settings	Ensure digital source; select proper surround mode; check speaker setup.
Remote not working	Batteries/obstructions	Replace batteries; point at IR sensor; remove obstacles.
Overheating	Ventilation/impedance	Ensure adequate ventilation; check speaker impedance.
Tuner no reception	Antenna/connections	Check antenna connections; reposition antennas; rescan stations.

Reset: Main power off for 30 seconds, then restart. Factory reset via setup menu if needed.

Service: 1-800-270-2744; www.marantz.com