Marantz SR 6002 Manual

The Marantz SR 6002 is a high-performance 7.1 channel AV receiver featuring 110W per channel, HDMI 1.3a connectivity, Dolby TrueHD and DTS-HD Master Audio decoding, Audyssey MultEQ auto calibration, multi-room capabilities, and extensive connectivity options. Below are key sections for setup, operation, features, and troubleshooting.

Features at a Glance

Key components: 7.1 channel amplifier, HDMI switching, Audyssey room correction, multi-zone audio, and extensive input/output options.

Feature	Description
Power Output	110W per channel (8 ohms, 20Hz-20kHz)
HDMI Ports	4 inputs, 1 output (HDMI 1.3a)
Audio Decoding	Dolby TrueHD, DTS-HD Master Audio
Room Correction	Audyssey MultEQ auto calibration
Multi-Zone	Zone 2 and Zone 3 audio output
Inputs	Component video, composite, analog audio, digital optical/coaxial
Network Ready	Ethernet port for firmware updates
Remote Control	Learning remote with backlight
Display	Fluorescent display with dimmer control
Setup Menu	On-screen display with intuitive interface

Installation

Unpack and inspect contents. Place in well-ventilated area.

1. Connect speakers: Use appropriate gauge speaker wire for each channel.
2. Connect video sources: Use HDMI for best quality; component/composite as alternatives.
3. Connect audio sources: Use digital inputs for surround sound; analog for stereo.
4. Connect subwoofer: Use LFE or line-level subwoofer output.
5. Plug into AC power.

WARNING! Ensure adequate ventilation; do not block cooling vents. Use proper gauge speaker wire.

First-Time Setup

Power on receiver; follow on-screen setup wizard.

1. Run Audyssey calibration: Connect included microphone and follow prompts.
2. Set speaker configuration: Specify size, distance, and crossover settings.
3. Configure inputs: Assign sources to input buttons.
4. Set video options: Configure HDMI control and video processing.
5. Network setup: Connect Ethernet for firmware updates.

CAUTION! Ensure all connections are secure before powering on.

Specifications

• Amplifier Section: 7.1 channels, 110W per channel (8 ohms)
• Frequency Response: 10Hz-100kHz (+1/-3dB)
• Total Harmonic Distortion: 0.05% (8 ohms, 20Hz-20kHz)
• HDMI: 4 in/1 out, version 1.3a, Deep Color, xvYCC
• Audio Decoding: Dolby Digital, DTS, Dolby TrueHD, DTS-HD Master Audio
• Inputs/Outputs: 8 analog audio, 6 digital (4 optical/2 coaxial), 5 video
• Multi-Zone: Zone 2 and Zone 3 pre-outs
• Power Consumption: 650W maximum, 75W standby
• Dimensions: 17.3" W × 6.4" H × 16.1" D
• Weight: 26.5 lbs

Controls and Settings

Front Panel: POWER, INPUT SELECTOR, VOLUME, HEADPHONE JACK, SETUP MIC.

Remote: POWER, INPUT SELECT, VOLUME, MUTE, MENU, AUDIO MODE, ZONE SELECT.

Audio Settings: Speaker configuration, distance, level, crossover. Video Settings: HDMI control, resolution, aspect ratio. Network Settings: IP configuration, firmware update. Multi-Zone: Zone 2/3 source selection and volume.

Connecting Devices

HDMI: Primary connection for HD video and audio. Component: For HD sources without HDMI. Analog: For legacy audio sources.

1. Turn off receiver and devices before connecting.
2. Use HDMI for video sources with audio.
3. Assign inputs in setup menu for easy selection.
4. Connect multi-zone speakers to appropriate terminals.

Tip: Use high-quality HDMI cables for best performance.

Audio Setup

Advanced audio configuration for optimal sound quality.

1. Run Audyssey MultEQ: Place microphone at listening position.
2. Manual speaker setup: Adjust distance, level, and crossover.
3. Audio modes: Select Dolby/DTS decoding or stereo modes.
4. Dynamic volume: Adjust for consistent listening levels.
5. Night mode: Compress dynamic range for late-night viewing.

WARNING! Ensure proper speaker polarity for correct phase alignment.

Multi-Room Operation

Zone 2 and Zone 3 capabilities for whole-home audio.

1. Connect Zone 2 speakers to dedicated terminals.
2. Select Zone 2 source using remote or front panel.
3. Set Zone 2 volume independently from main zone.
4. Use pre-outs for external amplification in additional zones.

Note: Some audio formats may not be available in secondary zones.

Care & Maintenance

Unplug before cleaning. Use soft, dry cloth for exterior. Keep ventilation openings clear.

CAUTION! Do not use liquid cleaners or aerosols. Avoid blocking ventilation ports.

Regulatory Information

FCC Part 15: Class B digital device compliant. CE marked for European market. Manufactured under license from Dolby Laboratories and DTS. For support, visit www.marantz.com or contact authorized service centers.

Troubleshooting

Symptom	Possible Cause	Corrective Action
No sound	Input selection/speaker wires	Check input selection; verify speaker connections; ensure mute is off.
No video	HDMI connection/settings	Verify HDMI cables; check input assignment; try different HDMI port.
Remote not working	Batteries/obstructions	Replace batteries; ensure line of sight to IR sensor.
Overheating	Ventilation blockage	Ensure adequate ventilation; clear vents; reduce volume if necessary.
Network issues	Ethernet connection	Check Ethernet cable; verify network settings; restart router.

Reset: Press and hold TUNER PRESET CH + and - while powering on for factory reset.

Service: Contact authorized Marantz service center; www.marantz.com