Marantz Receiver 7300 Manual

The Marantz Receiver 7300 is a high-performance audio/video receiver featuring Dolby Digital and DTS decoding, multiple audio/video inputs, 100 watts per channel, AM/FM tuner with 40 station presets, remote control, on-screen display, bass and treble controls, and multi-room audio capability. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

Features at a Glance

Key components: Dolby Digital/DTS decoder, AM/FM tuner, multiple audio/video inputs, remote control, speaker terminals.

Installation

Unpack and inspect contents. Place in well-ventilated area.

1. Connect speakers: Use speaker wire to connect front, center, surround speakers.
2. Connect audio sources: Use analog/digital inputs for CD player, tape deck, etc.
3. Connect video sources: Use composite/S-Video inputs for DVD player, VCR, etc.
4. Connect antenna: Attach AM loop and FM wire antennas.
5. Plug into AC power.

WARNING! Ensure proper ventilation; do not block vents. Use correct speaker impedance.

First-Time Setup

Power on receiver; follow on-screen prompts.

1. Auto speaker setup: Use built-in test tone for speaker level calibration.
2. Program radio stations: Use auto-scan to find and store FM/AM stations.
3. Set input assignments: Assign audio/video inputs to specific sources.
4. Configure surround mode: Select Dolby Digital/DTS for movie content.

CAUTION! Ensure all connections are secure before powering on.

Specifications

• Power Output: 100W x 5 channels (8 ohms)
• Frequency Response: 20Hz-20kHz (±0.5dB)
• Signal-to-Noise: 100dB (line level)
• Total Harmonic Distortion: 0.05% (rated power)
• Input Sensitivity: 200mV (line)
• Digital Inputs: 2 optical, 1 coaxial
• Video Inputs: 3 composite, 2 S-Video
• Tuner Section: AM/FM with RDS
• Power Consumption: 450W maximum
• Dimensions: 17.1" W x 6.3" H x 15.4" D

Controls and Settings

Front Panel: POWER, VOLUME, INPUT SELECT, TONE, MUTE, HEADPHONE.

Remote: POWER, Numeric buttons, INPUT SELECT, VOLUME, MUTE, SURROUND MODE, TUNER PRESETS, SETUP.

Audio: Bass, treble, balance, loudness, surround mode (Dolby Digital, DTS, Pro Logic). Video: Input selection, OSD settings. Tuner: Auto-scan, manual tuning, preset memory. System: Speaker setup, input rename, factory reset.

Connecting Devices

Audio: Analog/digital inputs. Video: Composite/S-Video inputs. Speakers: 5.1 channel terminals.

1. Turn off receiver and devices before connecting.
2. Match cable types to inputs (analog/digital, composite/S-Video).
3. Connect speakers observing correct polarity (+/-).
4. Select input via INPUT SELECT or remote.

Tip: Use high-quality cables for best audio/video performance.

Audio Setup

Optimize sound for your room and speakers.

1. Speaker levels: Use test tone to balance all channels.
2. Surround modes: Select Dolby Digital for movies, DTS for music.
3. Tone controls: Adjust bass/treble to preference.
4. Loudness: Engage for better low-volume listening.
5. Dynamic range: Adjust for night viewing.

WARNING! Avoid extreme volume levels to prevent speaker damage.

Multi-Room Operation

Zone 2 output for second room audio.

1. Connect speakers to Zone 2 terminals.
2. Select Zone 2 source independently from main zone.
3. Control volume separately for each zone.
4. Use remote in second room with IR extender.

Care & Maintenance

Unplug before cleaning. Use soft, dry cloth only; no liquids or chemicals.

CAUTION! Keep away from moisture and heat sources. Ensure proper ventilation.

Regulatory Information

FCC Part 15: Class B digital device; complies with interference limits for residential use. Copyright © 2006 Marantz; trademarks of Marantz America, Inc. For support, visit www.marantz.com or contact 1-800-270-2873.

Troubleshooting

Reset: Press POWER while holding TONE buttons for 5 seconds.

Service: 1-800-270-2873; www.marantz.com