Marantz PM7001 KI Manual

The Marantz PM7001 KI is a high-performance integrated stereo amplifier featuring Ken Ishiwata signature tuning, 70 watts per channel (8 ohms), high-current power supply, gold-plated connectors, MM phono input, multiple line inputs, preamp outputs, headphone jack, and remote control. Below are key sections for features, installation, operation, specifications, and maintenance.

Features at a Glance

Key components: High-current power transformer, gold-plated RCA connectors, MM phono stage, remote control, headphone output, preamp outputs.

Installation

Unpack and inspect contents. Place on stable, level surface with adequate ventilation.

1. Connect speakers: Use high-quality speaker cables to Speaker A/B terminals.
2. Connect audio sources: Use gold-plated RCA cables to appropriate inputs.
3. Connect turntable: Use Phono MM input for moving magnet cartridges.
4. Plug into AC power outlet.

WARNING! Ensure proper ventilation; do not block ventilation slots. Use correct speaker impedance (4-16Ω).

First-Time Setup

Power on amplifier; allow warm-up for optimal performance.

1. Speaker selection: Choose Speaker A, B, or A+B using front panel buttons.
2. Input selection: Rotate input selector knob to desired source.
3. Volume control: Start at minimum volume and gradually increase.
4. Balance adjustment: Use balance control if needed for room acoustics.

CAUTION! Always turn volume to minimum before powering on/off to protect speakers.

Specifications

• Power Output: 70W + 70W (8Ω), 100W + 100W (4Ω)
• Inputs: Phono MM, CD, Tuner, Tape, Aux, Tape Out
• Outputs: Speaker A/B, Pre Out, Headphone (6.3mm)
• Frequency Response: 5Hz-50kHz (+0/-3dB)
• Total Harmonic Distortion: 0.02% (20Hz-20kHz)
• Damping Factor: 200 (8Ω, 1kHz)
• Input Sensitivity/Impedance: 200mV/47kΩ (Line), 2.5mV/47kΩ (Phono)
• Power Consumption: 230W (max), 45W (no signal)
• Power Requirements: 120V AC, 60Hz (US model)

Controls and Connections

Front Panel: Power switch, Input selector, Volume control, Balance control, Speaker A/B buttons, Headphone jack, Tape monitor.

Rear Panel: Power cord input, Phono MM, CD, Tuner, Tape, Aux inputs, Speaker terminals (A/B), Pre Out, Ground terminal.

Remote Control: Power, Input selection, Volume up/down, Mute, Tape monitor.

Connecting Audio Sources

CD Player: Connect to CD input. Turntable: Connect to Phono MM input (ensure ground wire connected). Tuner: Connect to Tuner input. Tape Deck: Connect to Tape input/output.

1. Turn off amplifier before making connections.
2. Use high-quality interconnects for best performance.
3. Match left/right channels correctly (red/white RCA).
4. Ensure secure connections to prevent signal loss.

Tip: Keep signal cables away from power cords to minimize interference.

Operation Guide

Daily operation procedures for optimal performance.

1. Power on: Switch on rear power button, then use front power or remote.
2. Source selection: Rotate input selector or use remote control buttons.
3. Volume adjustment: Use front knob or remote volume controls.
4. Speaker selection: Choose between Speaker A, B, or both.
5. Headphone use: Plug into front jack automatically mutes speakers.
6. Tape monitoring: Use for recording and playback monitoring.

WARNING! Do not operate with covers removed. Avoid excessive volume levels.

Maintenance & Care

Unplug before cleaning. Use soft, dry cloth for exterior. Keep away from moisture and extreme temperatures.

CAUTION! Do not use chemical cleaners. Service by qualified personnel only.

Regulatory Information

FCC Part 15: Class B digital device; complies with interference limits. CE certified for European markets. Copyright © 2006 Marantz; trademarks of Marantz America, Inc. For support, visit www.marantz.com or contact authorized service centers.

Troubleshooting

Reset: Power cycle amplifier if issues persist.

Service: Contact authorized Marantz service center; www.marantz.com