Marantz PM6010OSE Manual

The Marantz PM6010OSE is a high-quality stereo integrated amplifier featuring 60 watts per channel, gold-plated connectors, MM phono input, CD direct input, tone controls, headphone output, and remote control capability. Designed for audiophiles seeking superior sound quality with Marantz's signature musical performance. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting Devices 7. Operation Guidelines 8. Maintenance 9. Regulatory Information 10. Troubleshooting

Features at a Glance

Key components: High-current power supply, gold-plated RCA connectors, MM phono stage, CD direct mode, tone defeat, speaker A/B switching.

Feature	Description
Power Output	60 watts per channel (8 ohms)
Inputs	Phono MM, CD, Tuner, Tape, Aux
Outputs	Speaker A/B, Tape out, Headphone
Frequency Response	10Hz - 20kHz (±0.5dB)
Signal-to-Noise Ratio	96dB (CD input)
Tone Controls	Bass ±10dB, Treble ±10dB
Remote Control	RC2000MS compatible
Dimensions	440 x 135 x 370mm (WxHxD)
Weight	8.5 kg
Power Consumption	230W maximum

Installation

Unpack and inspect contents. Place on stable, level surface with adequate ventilation.

Connect speakers: Use high-quality speaker cables to Speaker A/B terminals.
Connect audio sources: Use gold-plated RCA cables for CD player, turntable, etc.
Connect power cord: Use supplied power cord and appropriate wall outlet.
Ensure proper ventilation: Leave at least 10cm clearance on all sides.

WARNING! Ensure proper grounding. Do not block ventilation slots. Use correct speaker impedance (4-16 ohms).

First-Time Setup

Power on amplifier; follow initial setup procedure.

Speaker connection: Connect speakers to appropriate terminals (A or B).
Source connection: Connect CD player to CD input, turntable to Phono input.
Power up: Turn volume to minimum, then power on amplifier.
Initial listening: Start with low volume and adjust tone controls as needed.
Remote setup: Install batteries in RC2000MS remote control.

CAUTION! Always turn volume to minimum before powering on/off. Match speaker polarity correctly.

Specifications

Power Output: 60W + 60W (8 ohms, 20Hz-20kHz)
Total Harmonic Distortion: 0.02% (20Hz-20kHz)
Input Sensitivity: Phono: 2.5mV, CD: 200mV
Input Impedance: Phono: 47k ohms, CD: 20k ohms
Damping Factor: 100 (8 ohms, 1kHz)
Power Supply: AC 120V/230V, 50/60Hz
Dimensions: 440 x 135 x 370 mm (W x H x D)
Weight: 8.5 kg

Controls and Settings

Front Panel: Power switch, Volume control, Input selector, Tone controls, Speaker selector, Headphone jack.

Rear Panel: Gold-plated RCA inputs, Speaker terminals, AC power input, Fuse holder.

Input Selection: Phono, CD, Tuner, Tape, Aux. Tone Controls: Bass ±10dB at 100Hz, Treble ±10dB at 10kHz. Speaker Selection: A, B, A+B. Special Features: CD Direct mode bypasses tone controls, Tone Defeat switch.

Connecting Devices

Audio Sources: Phono for turntable, CD for CD player, Aux for additional sources.

Turn off amplifier before connecting devices.
Use high-quality shielded RCA cables for all connections.
For turntable: Connect to Phono input only (MM cartridge compatible).
Speaker connections: Ensure positive/negative polarity is maintained.
Tape deck: Use Tape input/output for recording capability.

Tip: Use CD Direct mode for best sound quality from CD players.

Operation Guidelines

Optimal performance settings and daily operation.

Power sequence: Turn on sources first, then amplifier. Reverse for shutdown.
Volume control: Start at minimum, increase gradually to desired level.
Input selection: Choose appropriate input for each source.
Tone controls: Adjust to personal preference or use Tone Defeat for pure signal.
Speaker selection: Use A, B, or A+B for multiple speaker pairs.
Headphone use: Automatically mutes speaker output when headphones connected.

WARNING! Do not operate with covers removed. Avoid excessive volume levels.

Maintenance

Regular maintenance for optimal performance and longevity.

Cleaning: Use dry, soft cloth only. Do not use chemicals or solvents.
Ventilation: Keep ventilation slots clear of dust and obstructions.
Connections: Periodically check and clean connector surfaces.
Fuse replacement: Use only specified fuse rating (T2A/250V).

CAUTION! Unplug from power before cleaning. Do not open chassis.

Regulatory Information

CE compliant. Manufactured to international safety standards. Copyright © Marantz. For technical support and service, contact authorized Marantz service centers. Specifications subject to change without notice.

Troubleshooting

Symptom	Possible Cause	Corrective Action
No sound	Volume, input selection, speaker connections	Check volume level, input selection, speaker connections and cables
Distorted sound	Overload, incorrect connections	Reduce volume, check source levels, verify speaker impedance
Hum or noise	Grounding, cable issues	Check grounding, use shielded cables, separate from power cables
Remote not working	Batteries, line of sight	Replace batteries, ensure clear path to IR sensor
One channel silent	Cable, balance setting	Check RCA cables, balance control, speaker connections

Service: Contact authorized Marantz service center for internal repairs.

Warranty: Refer to warranty card for terms and conditions.