Marantz PM-66SE User Manual

The Marantz PM-66SE is a high-quality stereo integrated amplifier featuring 60 watts per channel, MM/MC phono input, CD direct input, tone controls, headphone output, and remote control capability. Designed for audiophiles seeking exceptional sound quality with versatile connectivity options. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting Devices 7. Operation Guide 8. Remote Control Functions 9. Care & Maintenance 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: High-current power amplifier, MM/MC phono stage, CD direct input, tone controls, headphone output, remote sensor.

Feature	Description
Power Output	60 watts per channel (8 ohms)
Phono Input	MM/MC cartridge compatible
CD Direct	Pure signal path for CD players
Tone Controls	Bass and treble adjustment
Headphone Output	6.3mm jack for private listening
Remote Control	RC-66SE compatible
Input Selector	Phono, CD, Tuner, Aux, Tape
Speaker Selector	A/B speaker outputs
Power Switch	Main power on/off
Volume Control	Motorized potentiometer

Installation

Unpack and inspect contents. Place on stable, vibration-free surface.

Connect speakers: Use high-quality speaker cables to A/B terminals.
Connect audio sources: Phono for turntable, CD for CD player, etc.
Connect power cord: Use supplied power cable to AC outlet.
Connect remote sensor: For remote control operation.

WARNING! Ensure proper ventilation; do not block heat sinks. Use correct speaker impedance.

First-Time Setup

Power on amplifier; follow initial setup procedure.

Select input source: Rotate INPUT SELECTOR to desired source.
Adjust volume: Start at minimum volume and increase gradually.
Set tone controls: Start at flat position (12 o'clock).
Select speakers: Choose A or B speakers using front panel switch.
Phono setup: Set correct impedance for MM/MC cartridges.

CAUTION! Always turn volume to minimum before powering on/off.

Specifications

Power Output: 60W + 60W (8 ohms, 20Hz-20kHz)
Total Harmonic Distortion: 0.005%
Frequency Response: 5Hz-50kHz (+0/-3dB)
Input Sensitivity: Phono MM: 2.5mV, Phono MC: 0.2mV
Signal-to-Noise Ratio: 96dB (line inputs)
Inputs: Phono, CD, Tuner, Aux, Tape
Outputs: Tape out, Headphone, Speaker A/B
Power Requirements: 220-240V AC, 50/60Hz
Dimensions: 440 x 125 x 355mm (W x H x D)
Weight: 8.5 kg

Controls and Settings

Front Panel: Power switch, Input selector, Volume control, Tone controls, Speaker selector, Headphone jack.

Rear Panel: AC input, Phono inputs, Line inputs, Speaker terminals, Tape loops.

Tone Controls: Bass ±10dB at 100Hz, Treble ±10dB at 10kHz. Input Selector: Phono, CD, Tuner, Aux, Tape. Speaker Selector: A, B, A+B, Off. Volume Control: Motorized with remote operation.

Connecting Devices

Phono: Connect turntable ground wire. CD: Use CD direct input for best quality. Speakers: Ensure correct polarity.

Turn off amplifier before connecting devices.
Use high-quality interconnects for best performance.
Match cable colors (red-right, white-left).
Secure speaker connections tightly.
Connect turntable ground wire to ground terminal.

Tip: Keep signal cables away from power cables to reduce interference.

Operation Guide

Basic operation procedures for optimal performance.

Power on: Switch main power on; wait for relay click.
Select source: Choose appropriate input for your audio source.
Adjust volume: Start low and increase to desired level.
Tone adjustment: Use bass/treble controls to suit room acoustics.
Speaker selection: Choose A, B, or both speaker sets.
Headphone use: Plug in headphones; speakers mute automatically.
Tape recording: Use tape monitor for recording from any source.

WARNING! Do not operate without proper ventilation. Avoid shorting speaker terminals.

Remote Control Functions

RC-66SE remote control operation guide.

Button	Function
Power	Standby/operate mode
Volume +/-	Adjust volume level
Mute	Instant mute/unmute
Input Select	Cycle through input sources
CD Direct	Engage CD direct mode
Tone Bypass	Defeat tone controls

Remote requires 2x AAA batteries. Point at front panel sensor within 8 meters.

Care & Maintenance

Unplug before cleaning. Use soft, dry cloth for exterior. Clean controls with contact cleaner if needed.

CAUTION! Do not use chemical cleaners. Keep away from moisture and extreme temperatures.

Regulatory Information

CE compliant. Manufactured to international safety standards. Copyright © Marantz. For support, visit www.marantz.com or contact authorized service centers. This product complies with EU directives for electronic equipment.

Troubleshooting

Symptom	Possible Cause	Corrective Action
No sound	Volume/mute/speakers	Check volume setting; ensure mute off; verify speaker connections.
Distorted sound	Overload/speakers	Reduce volume; check speaker impedance; inspect cables.
Hum/buzz	Grounding/cables	Check turntable ground; ensure proper cable routing; use shielded cables.
Remote not working	Batteries/obstacles	Replace batteries; ensure line of sight to sensor; check distance.
One channel silent	Cables/balance	Check interconnects; verify balance control; test with different source.

Service: Contact authorized Marantz service center for internal repairs.

Support: www.marantz.com