marantz nr1602 manual pdf

The Marantz NR1602 is a slim 7.2-channel AV receiver featuring HDMI connectivity, network audio streaming, Audyssey room correction, multi-zone audio, and advanced audio processing. With 50 watts per channel, built-in Wi-Fi and Ethernet, AirPlay compatibility, and support for high-resolution audio formats, this receiver delivers premium home theater performance in a compact design. Below are key sections for setup, features, connectivity, operation, and troubleshooting.

1. Features at a Glance 2. Installation and Setup 3. Network Configuration 4. Specifications 5. Controls and Settings 6. Connecting Devices 7. Audio Configuration 8. Multi-Zone Operation 9. Care & Maintenance 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Slim chassis design, front panel display, remote control, speaker terminals, HDMI inputs/outputs, network ports, and audio inputs.

Feature	Description
HDMI Inputs	6 HDMI inputs with 3D and ARC support
Network Connectivity	Built-in Wi-Fi and Ethernet for streaming
Audio Formats	Dolby TrueHD, DTS-HD Master Audio
Audyssey Room Correction	Auto speaker calibration with included microphone
Multi-Zone Audio	Zone 2 audio output capability
AirPlay Support	Wireless audio streaming from Apple devices
Power Output	50 watts per channel (7 channels driven)
Front Panel Inputs	USB, analog audio, composite video
Remote Control	Learning remote with backlight
Setup Assistant	Guided on-screen configuration

Installation and Setup

Unpack and inspect contents. Place in well-ventilated area.

Connect speakers: Use appropriate gauge speaker wire for each channel.
Connect HDMI devices: Use high-speed HDMI cables for video sources.
Connect network: Use Ethernet cable or configure Wi-Fi for streaming.
Connect subwoofer: Use RCA cable for LFE output to powered sub.
Plug into AC power and turn on.

WARNING! Ensure adequate ventilation; do not block cooling vents. Use proper speaker impedance (6-16 ohms).

Network Configuration

Access network settings through on-screen menu.

Wired connection: Connect Ethernet cable to router.
Wireless setup: Select Wi-Fi network and enter password.
Network services: Enable AirPlay, internet radio, and media streaming.
Firmware updates: Check for and install latest firmware.

NOTE: Stable network connection required for streaming services and firmware updates.

Specifications

Amplifier Section: 7.2 channels, 50W per channel (8 ohms, 20Hz-20kHz)
HDMI: 6 inputs, 1 output (3D, ARC, 4K pass-through)
Network: Ethernet, built-in Wi-Fi (802.11n)
Audio Decoding: Dolby TrueHD, DTS-HD Master Audio, Dolby Digital Plus
Room Correction: Audyssey MultEQ, Dynamic Volume, Dynamic EQ
Streaming: AirPlay, internet radio, DLNA 1.5
Inputs/Outputs: 6 analog audio, 2 component video, 2 composite video
Power Supply: 120V AC, 60Hz
Dimensions: 17.3" W x 4.1" H x 13.8" D

Controls and Settings

Access menu system via front panel or remote control. Front Panel: POWER, INPUT SELECT, VOLUME, SETUP, STATUS.

Remote: POWER, INPUT SELECT, VOLUME, MUTE, SETUP, AUDIO, ZONE 2, PRESET, NAVIGATION buttons.

Audio Settings: Speaker configuration, crossover, distance, level calibration. Video Settings: HDMI setup, resolution, video mode. Network Settings: Wi-Fi configuration, service enablement. System Settings: OSD language, auto standby, firmware update.

Connecting Devices

HDMI: Primary connection for modern AV components. Analog: For legacy audio components. Network: For streaming and control.

Turn off receiver and components before connecting.
Use HDMI for video sources when possible for best quality.
Assign inputs in menu system for easy selection.
Connect network cable or configure wireless connection.

Tip: Label cables for easy identification during setup.

Audio Configuration

Run Audyssey room calibration for optimal sound.

Connect included microphone to front panel SETUP MIC jack.
Position microphone at primary listening position.
Follow on-screen prompts for measurement positions.
Save calibration results and make manual adjustments if needed.
Configure speaker sizes, crossovers, and distances.
Set up subwoofer level and phase alignment.

NOTE: Perform calibration in quiet environment for accurate results.

Multi-Zone Operation

Zone 2 audio for second room listening.

Connect Zone 2 speakers to assigned terminals.
Enable Zone 2 in menu system.
Select source for Zone 2 operation.
Control volume independently from main zone.
Use remote or front panel for Zone 2 control.

NOTE: Zone 2 operates with analog sources only when main zone is active.

Care & Maintenance

Unplug before cleaning. Use soft, dry cloth for exterior. Keep vents clear of dust.

CAUTION! Do not use liquid cleaners. Avoid moisture near ventilation openings.

Regulatory Information

FCC Part 15: Class B digital device compliant. Manufactured under license from Dolby Laboratories. DTS and DTS-HD are registered trademarks. For support, visit www.marantz.com or contact authorized service centers.

Troubleshooting

Symptom	Possible Cause	Corrective Action
No power	Power cord, standby mode	Check power connection; ensure unit is not in standby.
No sound	Input selection, mute, volume	Verify input selection; check mute status; adjust volume.
No video	HDMI connection, input	Check HDMI cable; verify correct input selection.
Network issues	Connection, settings	Verify network connection; check network settings.
Remote not working	Batteries, line of sight	Replace batteries; ensure clear path to IR sensor.

Reset: Press and hold STATUS and ENTER while powering on for factory reset.

Service: Contact authorized Marantz service center for repairs.