Marantz NR1403 Slimline AV Receiver Manual

The Marantz NR1403 is a slimline 5.1-channel AV receiver featuring 50 watts per channel, HDMI connectivity with 3D and Audio Return Channel support, built-in Bluetooth audio streaming, Audyssey MultEQ auto room calibration, multi-room audio capability, and compatibility with various audio formats including Dolby TrueHD and DTS-HD Master Audio. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting Devices 7. Audio Setup and Calibration 8. Network and Bluetooth Features 9. Care & Cleaning 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Slimline chassis design, HDMI inputs/outputs, Bluetooth antenna, speaker terminals, remote control, front panel display, and setup microphone port.

Feature	Description
HDMI Inputs	4 HDMI inputs with 3D and ARC support
Power Output	50W per channel (8 ohms, 20Hz-20kHz)
Bluetooth	Built-in audio streaming capability
Audyssey MultEQ	Auto room calibration system
Audio Formats	Dolby TrueHD, DTS-HD Master Audio
Multi-room	Zone 2 audio output capability
Inputs	Composite video, analog audio, optical digital
Outputs	Subwoofer pre-out, Zone 2 line out
Remote Control	Learning remote with backlight
Display	Front panel fluorescent display

Installation

Unpack and inspect contents. Place in well-ventilated area.

Connect speakers: Match polarity (+/-) to speaker terminals for all 5.1 channels.
Connect HDMI devices: Use HDMI inputs for Blu-ray players, gaming consoles, etc.
Connect TV: Use HDMI OUT (ARC) to television for audio return channel.
Connect subwoofer: Use subwoofer pre-out for powered sub.
Plug into AC power.

WARNING! Ensure adequate ventilation; do not block cooling vents. Use proper speaker wire gauge.

First-Time Setup

Power on receiver; follow on-screen setup wizard.

Speaker connection: Verify all speakers are properly connected.
Audyssey calibration: Connect setup microphone and run auto calibration.
Input assignment: Assign sources to appropriate inputs (BD, GAME, etc.).
Network setup: Configure Bluetooth pairing and network settings.
Audio settings: Adjust crossover, distance, and level settings.

CAUTION! Ensure all connections are secure before powering on.

Specifications

Amplifier Section: 5.1 channels, 50W per channel (8 ohms)
HDMI: 4 inputs, 1 output with ARC and 3D support
Audio Decoding: Dolby TrueHD, DTS-HD Master Audio
Room Correction: Audyssey MultEQ auto calibration
Wireless: Built-in Bluetooth audio streaming
Inputs: 4 HDMI, 2 composite video, 2 optical digital, 2 coaxial digital
Outputs: Subwoofer pre-out, Zone 2 line out, headphone jack
Power Consumption: 65W (standby: 0.3W)
Dimensions: 17.3" W x 4.1" H x 12.9" D

Controls and Settings

Access menu system via front panel or remote control. Front Panel: POWER, INPUT SELECT, VOLUME, SETUP, TONE controls.

Remote: POWER, INPUT SELECT, VOLUME, MUTE, SETUP, AUDIO, TONE, ZONE 2, Bluetooth pairing.

Audio Settings: Speaker configuration, crossover, distance, level calibration. Video Settings: HDMI control, resolution output. Network: Bluetooth pairing, firmware updates. System: OSD language, auto standby, reset options.

Connecting Devices

HDMI: Primary connection for modern AV components. Analog: Composite video and stereo audio inputs. Digital: Optical and coaxial inputs for legacy devices.

Turn off receiver and devices before connecting.
Use high-speed HDMI cables for best performance.
Assign inputs in setup menu for easy selection.
Connect Zone 2 speakers for multi-room audio.

Tip: Label cables for easy identification during setup.

Audio Setup and Calibration

Audyssey MultEQ provides automatic room correction.

Place setup microphone at primary listening position.
Run auto calibration from setup menu.
Verify speaker sizes and crossover settings.
Adjust channel levels manually if needed.
Set distance measurements for proper timing.
Configure subwoofer crossover and phase.
Save settings and test with various content.

WARNING! Ensure quiet environment during calibration for accurate results.

Network and Bluetooth Features

Bluetooth audio streaming from compatible devices.

Enable Bluetooth in network settings.
Put receiver in pairing mode.
Search for "Marantz NR1403" on your device.
Connect and stream audio wirelessly.
Use remote or front panel to control playback.

Note: Bluetooth range approximately 30 feet. Keep antenna unobstructed.

Care & Cleaning

Unplug before cleaning. Use soft, dry cloth for exterior. Compressed air for ventilation ports.

CAUTION! Do not use liquid cleaners. Avoid moisture near electrical components.

Regulatory Information

FCC Part 15: Class B digital device compliant. CE marked for European market. Manufactured under license from Dolby Laboratories. DTS and DTS-HD are registered trademarks. For support, visit www.marantz.com or contact authorized service centers.

Troubleshooting

Symptom	Possible Cause	Corrective Action
No sound from speakers	Speaker wires/input selection	Check speaker connections; verify input source; adjust volume.
HDMI no signal	Cables/input assignment	Ensure HDMI cables seated properly; check input assignment.
Bluetooth not connecting	Pairing mode/distance	Put receiver in pairing mode; move device closer; reset pairing.
Overheating	Ventilation blockage	Ensure adequate ventilation; clear vents of dust and obstructions.
Remote not working	Batteries/obstacles	Replace batteries; ensure line of sight to IR sensor.

Reset: Press and hold TONE and STATUS while powering on for factory reset.

Service: Contact authorized Marantz service center; www.marantz.com