Marantz Manual SR6011

The Marantz SR6011 is a 9.2-channel AV receiver with 4K Ultra HD video pass-through, Dolby Atmos and DTS:X object-based audio, built-in Wi-Fi and Bluetooth, AirPlay, HEOS multi-room audio, Audyssey room calibration, and support for high-resolution audio formats. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

Features at a Glance

Key components: 9.2-channel amplifier, Audyssey MultEQ XT32 room calibration, HEOS built-in, Dolby Atmos and DTS:X support, 8 HDMI inputs, phono input, Ethernet and Wi-Fi connectivity.

Feature	Description
Amplifier Channels	9.2 channels (110W per channel at 8 ohms)
Audio Formats	Dolby Atmos, DTS:X, Dolby TrueHD, DTS-HD Master Audio
Video Support	4K/60Hz pass-through, HDR10, Dolby Vision, HLG
Network Features	Built-in Wi-Fi, Bluetooth, AirPlay 2, HEOS multi-room
HDMI Inputs	8 inputs (all HDCP 2.2 compliant)
HDMI Outputs	2 outputs (Main and Zone 2)
Room Calibration	Audyssey MultEQ XT32 with Sub EQ HT
Phono Input	MM phono stage for turntable connection
Multi-room Audio	HEOS technology for whole-home audio
Control Options	Remote control, Marantz AVR Remote app

Installation

Unpack and inspect contents. Place in well-ventilated area.

1. Connect speakers: Use appropriate gauge speaker wire for all channels.
2. Connect subwoofer: Use RCA cable to LFE input on subwoofer.
3. Connect video sources: Use HDMI cables for 4K devices.
4. Connect network: Use Ethernet cable or configure Wi-Fi.
5. Plug into AC power.

WARNING! Ensure adequate ventilation; do not block vents. Unit may become hot during operation.

First-Time Setup

Power on receiver; follow on-screen setup assistant.

1. Run Audyssey calibration: Connect included microphone and follow prompts.
2. Configure inputs: Assign HDMI inputs to specific sources.
3. Set up network: Connect via Ethernet or configure Wi-Fi settings.
4. Configure audio: Set speaker sizes, distances, and crossover frequencies.
5. Update firmware: Check for and install latest firmware updates.

CAUTION! Ensure proper speaker polarity and secure connections.

Specifications

• Power Output: 110W per channel (8 ohms, 20Hz-20kHz, 0.08% THD)
• Frequency Response: 10Hz-100kHz (+1, -3dB)
• Total Harmonic Distortion: 0.08% (20Hz-20kHz at 110W)
• Signal-to-Noise Ratio: 100dB (line level)
• HDMI: 8 inputs, 2 outputs (4K/60Hz, HDR, Dolby Vision)
• Network: Ethernet, Wi-Fi (2.4GHz/5GHz), Bluetooth
• Audio Decoding: Dolby Atmos, DTS:X, Auro-3D
• Room Correction: Audyssey MultEQ XT32, Sub EQ HT
• Power Consumption: 710W maximum, 65W standby
• Dimensions: 17.3" W × 6.4" H × 15.7" D

Controls and Settings

Access settings via front panel or remote control. Front Panel: POWER, INPUT SELECT, VOLUME, SETUP, TONE CONTROL.

Remote: POWER, INPUT SELECT, VOLUME, MUTE, SETUP, OPTIONS, AUDIO, ZONE 2, HEOS.

Audio: Speaker configuration, crossover settings, tone controls, Audyssey settings. Video: Resolution, HDMI settings, video mode. Network: Wi-Fi setup, Bluetooth pairing, firmware update. System: GUI settings, remote control setup, zone configuration.

Connecting Devices

HDMI: Connect 4K sources to HDMI inputs. Analog: Use RCA inputs for legacy devices. Network: Ethernet or Wi-Fi for streaming.

1. Turn off receiver and devices before connecting.
2. Use high-speed HDMI cables for 4K content.
3. Assign inputs in setup menu for easy source selection.
4. Connect turntable to PHONO input (MM cartridges only).

Tip: Label cables for easy identification during setup.

Network Setup

Supports wired and wireless network connections.

1. Wired: Connect Ethernet cable to router and receiver.
2. Wireless: Access network settings in setup menu, select Wi-Fi network.
3. HEOS setup: Download HEOS app, follow pairing instructions.
4. Streaming services: Access via HEOS app or front panel.
5. Firmware updates: Check regularly for performance improvements.

WARNING! Ensure stable network connection for optimal streaming performance.

Audio Calibration

Audyssey MultEQ XT32 room correction system.

1. Connect calibration microphone to MIC port.
2. Position microphone at primary listening position.
3. Follow on-screen instructions for multiple measurement positions.
4. Review and save calibration results.
5. Adjust settings manually if desired (crossover, levels, distances).

Note: Perform calibration in quiet environment for best results.

Care & Maintenance

Unplug before cleaning. Use soft, dry cloth only; avoid liquids.

Ensure adequate ventilation around unit. Clean ventilation openings regularly.

CAUTION! Do not block ventilation openings. Keep away from moisture and heat sources.

Regulatory Information

FCC Part 15: Class B digital device; complies with interference limits for residential use. Copyright © Marantz America LLC. For support, visit www.marantz.com or contact 1-800-370-3744. This product incorporates copyright protection technology.

Troubleshooting

Symptom	Possible Cause	Corrective Action
No sound	Input selection/speaker settings	Check input selection; verify speaker connections; run Audyssey calibration.
No video	HDMI connection/settings	Check HDMI cables; verify input assignment; try different HDMI input.
Network connection issues	Wi-Fi signal/router settings	Check network credentials; move closer to router; try wired connection.
HEOS not working	Network/app issues	Update HEOS app; restart receiver and mobile device; check network.
Overheating	Insufficient ventilation	Ensure adequate clearance around unit; clean ventilation openings.

Reset: Press and hold INFO and BACK buttons for 5 seconds to factory reset.

Service: 1-800-370-3744; www.marantz.com