marantz manual sr6009

The Marantz SR6009 is a high-performance 7.2 channel AV receiver with 4K Ultra HD video pass-through, built-in Wi-Fi and Bluetooth, AirPlay compatibility, Dolby Atmos and DTS:X support, Audyssey MultEQ XT room calibration, and 125 watts per channel. Below are key sections for features, installation, setup, operation, specifications, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting Devices 7. Network Features 8. Audio Calibration 9. Care & Maintenance 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: 7.2 channel amplifier, built-in Wi-Fi and Bluetooth, 4K Ultra HD pass-through, Dolby Atmos and DTS:X decoding, Audyssey MultEQ XT room calibration.

Feature	Description
Power Output	125 watts per channel (8 ohms, 20Hz-20kHz)
Audio Formats	Dolby Atmos, DTS:X, Dolby TrueHD, DTS-HD Master Audio
Video Support	4K Ultra HD pass-through, 3D compatible
Network Features	Built-in Wi-Fi, Bluetooth, AirPlay, Ethernet
Inputs/Outputs	8 HDMI inputs, 2 HDMI outputs, phono input, multi-room audio
Room Calibration	Audyssey MultEQ XT with setup microphone
Zone 2	Second zone audio output
Remote Control	RC025SR learning remote with backlight
Display	Front panel fluorescent display
Power Consumption	650W maximum

Installation

Unpack and inspect contents. Place in well-ventilated area.

Connect speakers: Match polarity (+ to +, - to -) for all 7 channels.
Connect subwoofer: Use LFE output for one or two subwoofers.
Connect video sources: Use HDMI inputs for best quality.
Connect network: Use Ethernet cable or configure Wi-Fi.
Plug into AC power.

WARNING! Ensure adequate ventilation; do not block vents. Use proper speaker wire gauge.

First-Time Setup

Power on receiver; follow on-screen setup wizard.

Run Audyssey calibration: Connect setup microphone, follow on-screen instructions.
Configure inputs: Assign HDMI inputs to specific sources.
Set up network: Connect via Ethernet or configure Wi-Fi settings.
Configure audio: Set speaker sizes, distances, crossover frequencies.
Set up zones: Configure Zone 2 if needed.

CAUTION! Ensure proper ventilation; allow space for heat dissipation.

Specifications

Amplifier Section: 7.2 channels, 125W per channel (8 ohms)
Frequency Response: 10Hz-100kHz (+1, -3dB)
Total Harmonic Distortion: 0.05% (20Hz-20kHz)
Signal-to-Noise Ratio: 100dB (line level)
HDMI: 8 inputs, 2 outputs (4K/60Hz, 3D, ARC)
Network: Wi-Fi (802.11a/b/g/n), Bluetooth, Ethernet
Audio Decoding: Dolby Atmos, DTS:X, Dolby TrueHD, DTS-HD Master Audio
Room Correction: Audyssey MultEQ XT, Dynamic Volume, Dynamic EQ
Power Requirements: 120V AC, 60Hz
Dimensions: 17.3" W × 6.4" H × 15.7" D

Controls and Settings

Access menu via front panel or remote control. Front Panel: POWER, INPUT SELECT, VOLUME, TONE, SETUP.

Remote: POWER, INPUT SELECT, VOLUME, MUTE, SETUP, OPTIONS, AUDIO, ZONE 2.

Audio Settings: Speaker configuration, distance, level, crossover, Audyssey settings. Video Settings: Resolution, HDMI setup, video mode. Network Settings: Wi-Fi setup, firmware update, streaming services. System Settings: GUI language, auto standby, remote control setup.

Connecting Devices

HDMI: Primary connection for audio/video. Analog: RCA inputs for legacy devices. Network: Ethernet or Wi-Fi.

Turn off receiver and devices before connecting.
Use HDMI cables for modern sources (Blu-ray, game consoles).
Assign inputs in setup menu for easy selection.
Connect network for streaming and updates.

Tip: Use high-speed HDMI cables for 4K content and 3D playback.

Network Features

Supports streaming services, firmware updates, and multi-room audio.

Network setup: Connect via Ethernet or configure Wi-Fi in network settings.
Streaming services: Access Spotify, Pandora, SiriusXM via Marantz app.
AirPlay: Stream audio from Apple devices.
Bluetooth: Pair with smartphones and tablets for wireless audio.
Firmware updates: Check for updates automatically or manually.
Remote app: Control receiver with Marantz Remote App.

WARNING! Ensure stable network connection for streaming and updates.

Audio Calibration

Audyssey MultEQ XT room correction system with included microphone.

Place microphone at primary listening position.
Run Audyssey setup from menu (6 measurement positions recommended).
Review results: Speaker sizes, distances, levels, crossover frequencies.
Adjust settings manually if needed.
Enable Dynamic EQ and Dynamic Volume for optimal performance.

CAUTION! Ensure quiet environment during calibration measurements.

Care & Maintenance

Unplug before cleaning. Use soft, dry cloth only; no liquids or chemicals.

CAUTION! Do not block ventilation openings; keep away from moisture and heat sources.

Regulatory Information

FCC Part 15: Class B digital device; complies with interference limits for residential use. Copyright © Marantz America, LLC. For support, visit www.marantz.com or contact 1-800-370-3744. Bluetooth word mark and logos are registered trademarks.

Troubleshooting

Symptom	Possible Cause	Corrective Action
No sound	Input selection/speaker wires	Check input selection; verify speaker connections; ensure volume not muted.
No video	HDMI connection/settings	Check HDMI cables; verify input assignment; try different HDMI input.
Network not connecting	Wi-Fi/Ethernet settings	Check network credentials; verify Ethernet connection; restart router.
Remote not working	Batteries/obstructions	Replace batteries; ensure line of sight to IR sensor; check remote mode.
Overheating	Ventilation blockage	Ensure adequate ventilation; clear vents; reduce volume if excessive.

Reset: Press and hold POWER and SURROUND MODE buttons for 5 seconds.

Service: 1-800-370-3744; www.marantz.com