Marantz 9600 Manual

The Marantz 9600 is a high-performance audio/video receiver featuring advanced Dolby Digital and DTS processing, multi-room audio capabilities, extensive connectivity options, and sophisticated audio calibration. With 7-channel amplification, HDMI switching, network streaming capabilities, and premium build quality, it delivers exceptional home theater performance. Below are key sections for setup, features, operation, and troubleshooting.

Features at a Glance

Key components: 7-channel amplifier, HDMI inputs/outputs, network connectivity, multi-zone audio, Audyssey room calibration, remote control, and extensive audio processing.

Feature	Description
Amplifier Power	125W per channel (8 ohms, 20Hz-20kHz)
HDMI Inputs	6 inputs with 4K/60p pass-through
Network Connectivity	Ethernet and Wi-Fi for streaming services
Audio Formats	Dolby Atmos, DTS:X, Dolby TrueHD, DTS-HD Master Audio
Multi-room Audio	Zone 2 and Zone 3 output capabilities
Room Calibration	Audyssey MultEQ XT32 with Sub EQ HT
Bluetooth	Built-in for wireless audio streaming
HEOS Built-in	Multi-room audio system integration
Phono Input	MM phono stage for turntable connection
Front Panel Display	High-resolution fluorescent display

Installation

Unpack and inspect contents. Place in well-ventilated area.

1. Connect speakers: Use appropriate gauge speaker wire for each channel.
2. Connect source devices: Use HDMI cables for modern devices; analog for legacy equipment.
3. Connect TV: Use HDMI OUT (MAIN) to television.
4. Connect network: Use Ethernet cable or configure Wi-Fi.
5. Plug into AC power.

WARNING! Ensure adequate ventilation; do not block cooling vents. Unit may become hot during operation.

First-Time Setup

Power on receiver; follow on-screen setup wizard.

1. Run Audyssey calibration: Connect included microphone and follow prompts.
2. Configure inputs: Assign source names to each input.
3. Set up network: Connect to home network via Ethernet or Wi-Fi.
4. Configure audio settings: Set speaker sizes, distances, and levels.
5. Update firmware: Check for and install latest firmware updates.

CAUTION! During calibration, ensure quiet environment for accurate measurements.

Specifications

• Power Output: 125W x 7 (8 ohms, 20Hz-20kHz, 0.05% THD)
• Frequency Response: 10Hz-100kHz (+1, -3dB)
• Signal-to-Noise Ratio: 102dB (line level)
• HDMI: 6 inputs, 2 outputs (Main and Zone 2)
• Digital Inputs: 2 optical, 2 coaxial
• Analog Inputs: 7 line-level, 1 phono (MM)
• Network: Ethernet, Wi-Fi, Bluetooth
• Supported Audio Formats: Dolby Atmos, DTS:X, Dolby TrueHD, DTS-HD MA, FLAC, WAV, MP3, WMA
• Power Consumption: 650W maximum
• Dimensions: 17.3" W x 6.8" H x 15.7" D

Controls and Settings

Access menu system via front panel or remote control. Front Panel: POWER, INPUT SELECT, VOLUME, MENU, SETUP.

Remote: POWER, INPUT SELECT, VOLUME, MUTE, MENU, SETUP, navigation buttons, audio mode selection.

Audio Settings: Speaker configuration, crossover frequencies, distance settings, level calibration, tone controls. Video Settings: HDMI setup, resolution output, video mode. Network Settings: Wi-Fi setup, streaming services, firmware updates. System Settings: Input assignment, GUI settings, zone configuration.

Connecting Devices

HDMI: Primary connection for modern AV components. Analog: For legacy equipment and turntables. Network: Ethernet or Wi-Fi for streaming.

1. Turn off receiver and devices before connecting.
2. Use high-quality HDMI cables for best performance.
3. Assign appropriate input names in setup menu.
4. Configure audio settings for each input as needed.

Tip: Use the remote's input buttons to quickly switch between sources.

Audio Calibration

Audyssey MultEQ XT32 room correction system.

1. Connect calibration microphone to front panel MIC jack.
2. Position microphone at primary listening position.
3. Follow on-screen instructions for multiple measurement positions.
4. System automatically calculates optimal speaker settings.
5. Review and adjust settings as desired.
6. Save calibration results.

WARNING! Maintain complete silence during calibration measurements.

Network Setup

Connect to home network for streaming and control.

1. Wired: Connect Ethernet cable to router.
2. Wireless: Access network settings to connect to Wi-Fi.
3. Configure streaming services: Access music services via HEOS app.
4. Set up control: Enable network control for app operation.

Note: Firmware updates require network connection.

Care & Maintenance

Unplug before cleaning. Use soft, dry cloth for exterior. Compressed air for ventilation ports.

CAUTION! Do not use liquid cleaners. Avoid blocking ventilation openings. Keep away from moisture.

Regulatory Information

FCC Part 15: Class B digital device compliant. CE marked for European market. RoHS compliant. Copyright © 2024 Sound United LLC. Marantz is a registered trademark. For support, visit www.marantz.com or contact 1-800-370-3744.

Troubleshooting

Symptom	Possible Cause	Corrective Action
No sound from speakers	Speaker wires/input selection	Check speaker connections; verify input selection; ensure volume not muted.
No video output	HDMI connection/settings	Check HDMI cable connections; verify input/output resolution settings.
Network connection issues	Wi-Fi/Ethernet settings	Check network credentials; restart router; verify Ethernet connection.
Remote not working	Batteries/obstructions	Replace batteries; ensure clear line of sight to IR sensor.
Overheating	Ventilation blockage	Ensure adequate ventilation; clear vents of dust and obstructions.

Reset: Press and hold INFO and BACK buttons simultaneously for 5 seconds.

Service: 1-800-370-3744; www.marantz.com