marantz 1060 amp manual

The Marantz 1060 is a classic stereo integrated amplifier from the 1970s, renowned for its warm sound quality and robust construction. Featuring 30 watts per channel RMS power output, phono inputs for turntables, tape monitor loops, tone controls, and the distinctive Marantz blue-lit tuning dial. Below are key sections covering specifications, connections, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting Audio Sources 7. Operation Guide 8. Maintenance 9. Regulatory Information 10. Troubleshooting

Features at a Glance

Key components: Power amplifier section, preamplifier with phono stage, tone controls, input selector, volume/balance controls, tape monitor.

Feature	Description
Power Output	30 watts RMS per channel (8 ohms)
Phono Input	MM cartridge compatible with RIAA equalization
Tape Monitor	Dedicated tape input/output loops
Tone Controls	Bass and treble adjustment knobs
Input Selector	Phono, Tuner, Aux, Tape
Headphone Jack	Front panel 1/4" headphone output
Loudness Control	Compensates for low volume listening
Power Switch	Main power on/off with indicator light
Speaker Selector	A/B speaker outputs
Balance Control	Left/right channel balance adjustment

Installation

Unpack and inspect contents. Place on stable, well-ventilated surface.

Connect speakers: Use speaker wire to connect to A or B speaker terminals.
Connect audio sources: Phono for turntable, Tuner for radio, Aux for CD/other sources.
Connect tape deck: Use tape input/output jacks for recording/monitoring.
Plug into AC power outlet.

WARNING! Ensure proper ventilation; do not block heat sinks. Use correct speaker impedance (4-16 ohms).

First-Time Setup

Power on amplifier; allow 30 seconds for warm-up.

Set input selector: Choose appropriate source (Phono, Tuner, Aux).
Adjust volume: Start with volume at minimum, gradually increase.
Set tone controls: Begin with flat response (12 o'clock position).
Balance adjustment: Center balance control for equal left/right output.
Speaker selection: Choose A or B speakers as desired.

CAUTION! Avoid turning volume to maximum to prevent speaker damage.

Specifications

Power Output: 30 watts per channel RMS (8 ohms)
Total Harmonic Distortion: <0.3% at rated output
Frequency Response: 20Hz-20kHz ±1dB
Input Sensitivity: Phono: 2.5mV, Aux/Tuner: 150mV
Signal-to-Noise Ratio: Phono: 70dB, Aux: 85dB
Tone Controls: Bass: ±10dB at 100Hz, Treble: ±10dB at 10kHz
Power Requirements: 120V AC, 60Hz
Dimensions: 17" W × 4.5" H × 12" D
Weight: 22 lbs

Controls and Settings

Front Panel: Power switch, input selector, volume, balance, bass, treble, loudness, speaker selector, headphone jack.

Rear Panel: AC power cord, phono inputs, tuner/aux inputs, tape monitor jacks, speaker terminals.

Input Selection: Rotate selector knob to choose source. Tone Controls: Bass and treble knobs adjust frequency response. Loudness: Engages bass boost at low volumes. Balance: Adjusts left/right channel level. Speaker Selector: Choose A, B, or both speaker sets.

Connecting Audio Sources

Phono: Connect turntable ground wire and RCA cables. Tuner: Connect FM/AM tuner outputs. Aux: Connect CD player, tape deck, or other line-level sources.

Turn off amplifier before making connections.
Use quality RCA cables for all connections.
Ensure proper grounding for phono connections.
Match input type to source (phono for turntable only).

Tip: Keep signal cables away from power cords to reduce hum.

Operation Guide

Daily operation procedures for optimal performance.

Power on: Switch power button; wait for indicator light.
Select source: Turn input selector to desired position.
Adjust volume: Start low, increase gradually to desired level.
Tone adjustment: Use bass/treble controls to suit listening preference.
Loudness: Engage for low-volume listening enhancement.
Tape monitoring: Use tape monitor switch for recording/playback.
Headphone use: Plug headphones into front jack; speakers mute automatically.

WARNING! Do not operate with cover removed. Avoid liquid exposure.

Maintenance

Unplug before cleaning. Use soft, dry cloth for exterior. Compressed air for dust removal from vents.

CAUTION! No user-serviceable parts inside. Refer servicing to qualified personnel.

Regulatory Information

Troubleshooting

Symptom	Possible Cause	Corrective Action
No sound	Power/speaker connections	Check power cord; verify speaker connections; ensure input selected.
Hum or buzz	Grounding issues	Check phono ground connection; separate signal/power cables.
Distorted sound	Overload/damage	Reduce volume; check speaker impedance; inspect for damage.
One channel silent	Balance/connections	Adjust balance control; check RCA cables; clean controls.
Lights but no sound	Protection circuit	Check for shorted speakers; allow cool-down if overheated.

Service: Contact authorized Marantz service center for internal repairs.